Atelier

All projects · Kitchen

Kitchen console

Design final · shopping list priced

A freestanding console that covers the wall radiator, matches the worktop height and leaves the cabinet door on the right free. No back panel, so the radiator heat can still escape.

1300 × 420 × 920 mmsize
243,08 €required items
15 Nov 2026last update

Drawings

Front, side section and floor plan: joue positions, the 6 feet and the radiator behind the left bay.
Front, side section and floor plan: joue positions, the 6 feet and the radiator behind the left bay. Tap to open full size.
How the top is fixed to the joues: cleats, screw lengths and directions, and the foot doubler with its M8 insert.
How the top is fixed to the joues: cleats, screw lengths and directions, and the foot doubler with its M8 insert. Tap to open full size.
Cutting plan for the plywood, and the two steel flat bars glued under the top in the A–B bay.
Cutting plan for the plywood, and the two steel flat bars glued under the top in the A–B bay. Tap to open full size.
The 6 mm cover strip that hides the gap under joue A, and why it is not 18 mm.
The 6 mm cover strip that hides the gap under joue A, and why it is not 18 mm. Tap to open full size.

Key dimensions

Finished height
920 = 16 top + 884 joue + 20 foot
Depth
420 = 180 free at the back + 220 joue + 20 overhang
Joue positions
A at 0, B at 640, C at 1050 (C lines up with the cabinet edge) · bays 640 / 392 / 232
Shelf
622 × 216, top at 700, left bay only
Radiator
500 × 500, 140 from the floor, 125 deep · 55 mm air in front, 42 mm under the shelf
Reinforcement
2 steel flat bars 50 × 5 × 580 under the top, A–B bay only
Feet
6 adjustable M8 feet with felt pads, 20 mm, adjust 12–28

All sizes in mm. Material: 18 mm plywood, reused 16 mm worktop, two steel flat bars under the top.

Why it looks like this

  • Nothing is fixed to the wall. Two steel flat bars (50 × 5) glued under the top in the A–B bay give the stiffness: sag under 30 kg drops from about 8 mm to 1.4 mm (2.4 mm with 3 mm aluminium). Two wall brackets above the radiator stay an option for extra safety with a child at home.
  • Steel rather than a plywood doubler: 5 mm of steel is as stiff as 18 mm of wood, with far less height lost.
  • Joue A is full depth (380) for looks and stability. It stands 20 mm off the wall to clear the skirting.
  • A 6 mm cover strip at the foot of joue A hides the gap made by the feet. Only on the visible side.
  • Nothing goes below the top in the last 232 mm on the right, so the cabinet door still opens.
  • Only items sold directly by Leroy Merlin, for pickup at Nanterre.

What to build

Cutting list

Finished sizes, saw cuts already deducted (about 4 mm each): that is why the shelf is 216, not 220. Easiest: give the six plywood sizes to the store's cut-to-size service.

PartSize (mm)QtyFrom
Joue A884 × 380118 mm plywood
Joues B and C884 × 220218 mm plywood
Shelf622 × 216118 mm plywood
Foot doublers200 × 100318 mm plywood
Top1300 × 4201Reused 16 mm worktop
Cover strip, foot of joue A380 × 4015–6 mm plywood
Cleats, joue A360120 × 20 pine
Cleats, joues B and C200420 × 20 pine
Cleats, shelf200220 × 20 pine
Flat bars under the top580250 × 5 steel flat bar

Steps

  1. Do the four site checks below before anything is cut.
  2. Have the plywood cut at the store. Check every piece is square and to size before you leave.
  3. Iron the edge banding while the pieces are flat (wool setting, no steam): front and bottom edge of each joue, front and short edges of the shelf. Press with a block while it cools, trim with the cutter, sand lightly.
  4. Glue and screw a 200 × 100 doubler at the bottom of the inside face of each joue. Then drill the M8 inserts into the 36 mm.
  5. Glue and screw the 20 × 20 cleats at the top of each joue, flush with the top edge: two on B and C (200), one on the inside of A (360).
  6. Screw the shelf cleats onto joues A and B, at 700 from the finished floor.
  7. Lay the top face down, stand the three joues on it, check they are square and screw up through the cleats (4 × 30). Never leave a joue standing alone: it falls over.
  8. Glue the two steel flat bars under the top, A–B bay only. Degrease, pre-drill and countersink the bars, glue with MS polymer and screw 4 × 16 every 150 mm to clamp while it sets.
  9. Turn it over. Stick the felt pads and screw in the feet. Screw the shelf onto its cleats (4 × 16).
  10. Glue the cover strip on the outside of joue A, bottom edge 3 mm off the floor. Hold it with masking tape while it sets.
  11. Slide it into place. Set all feet to mid-travel, level joue C first (flush with the worktop), then A with the 1 m level, then lower B just until it touches. Check again after a week.
  12. Sand the edges, dust off, and apply the water-based varnish with a synthetic brush. Seal the edges well: coffee machine steam.

Before you buy

Measure or confirm these first. Tick them as you go: ticks stay on this device.

What to buy

243,08 €required
0,00 €optional
137,56 €tools, if missing
—left to buy (unticked)

Cart at Leroy Merlin

243,08 €

Prices checked on leroymerlin.fr, 15 Nov 2026. Free pickup at Nanterre. Not in this cart yet, but needed by the plans: a 2 m steel flat bar 50 × 5 (or STANDERS aluminium 50 × 3), MS polymer glue (Sika, Pattex) for metal on wood, and rust primer if you take steel.

  • Panneau contreplaqué naturel 250 × 122 cm, ép. 18 mm

    Requiredréf. 69124265Qty 1 × 129,00 €

    Joues A/B/C, shelf, foot doublers

    View at Leroy Merlin ↗

    129,00 €

  • Panneau contreplaqué naturel 80 × 40 cm, ép. 5 mm

    Requiredréf. 70753914Qty 1 × 8,99 €

    Cover strip at the foot of joue A

    View at Leroy Merlin ↗

    8,99 €

  • Tasseau sapin raboté 21 × 21 mm, L. 1 m

    Requiredréf. 82271765Qty 2 × 2,69 €

    Cleats for the top and the shelf

    View at Leroy Merlin ↗

    5,38 €

  • 2 vis de réglage + écrou HETTICH M8 × 60

    Requiredréf. 67557203Qty 3 × 3,99 €

    The 6 feet. Tap-in nuts included

    View at Leroy Merlin ↗

    11,97 €

  • Patin-feuille feutre adhésif STANDERS 175 × 200 mm

    Requiredréf. 85066285Qty 1 × 3,99 €

    Cut to size, under each foot

    View at Leroy Merlin ↗

    3,99 €

  • Vis tête fraisée STANDERS ø4 × 30 mm

    Requiredréf. 82231851Qty 1 × 7,99 €

    Cleats and foot doublers

    View at Leroy Merlin ↗

    7,99 €

  • Vis tête fraisée STANDERS ø4 × 16 mm

    Requiredréf. 82231803Qty 1 × 3,99 €

    Shelf onto its cleats

    View at Leroy Merlin ↗

    3,99 €

  • Bande de chant thermocollante chêne SPACEO 5 m × 23 mm

    Requiredréf. 67540900Qty 2 × 7,99 €

    Edges of joues and shelf, about 8 m

    View at Leroy Merlin ↗

    15,98 €

  • Colle SADER Bois pro D3, 750 g

    Requiredréf. 69645366Qty 1 × 18,90 €

    All wood gluing

    View at Leroy Merlin ↗

    18,90 €

  • Vernis V33 Cuisine & Bains incolore mat, 0,75 l

    Requiredréf. 69659506Qty 1 × 29,90 €

    Water-resistant finish

    View at Leroy Merlin ↗

    29,90 €

  • Set de 3 feuilles abrasives NORTON 230 × 280 mm

    Requiredréf. 85551351Qty 1 × 6,99 €

    Sanding edges and corners

    View at Leroy Merlin ↗

    6,99 €

Tools and consumables

137,56 €

Skip what you already own. Stock checked at Nanterre. No product links in the sheet, so these open a search.

Files and sources

Downloads

In Claude

These open in your Claude account and are private to you.